How to Raise pH in a Pool and Keep It There
Updated: 3 hours ago
Low pool pH comes up fast with soda ash, more slowly with baking soda, and without any product at all through aeration. Which route fits depends on what your alkalinity reading says, so test before you dose. Our team at Hawaiian Island Pools builds and services fiberglass pools around New Port Richey, Florida, and a pH reading that will not sit still is one of the most frequent questions we field after handover.
The working range sits between 7.2 and 7.6. Below it, water turns aggressive toward skin, eyes, plaster, and metal. Above it, chlorine loses most of its killing power and scale starts forming on surfaces and inside the heater. Corrosion that shows up on a pump seal or a heater core almost always traces back to months of low readings rather than one bad weekend, which is why our pump, filter, and heater servicing calls usually start with a water test rather than a parts order.
Why pool pH drifts low
Three things drive most of the low readings we see in Tampa Bay yards. Trichlor tablets, the sanitizer sitting in most floaters and feeders, are acidic, so every tablet that dissolves pulls pH down with it. Summer storms do the same from above, since rainwater is mildly acidic and arrives in volume here between June and September. A heavy hand with muriatic acid during a scale correction can overshoot by a full point in a single dose.
Low total alkalinity makes all of it worse. Alkalinity is the buffer that resists pH movement, so a pool sitting at 50 ppm will swing after a light rain while one holding 100 ppm barely moves. If your pH refuses to stay put no matter how much increaser goes in, alkalinity is usually the real problem and the place to start.
Chemical options that raise pH
Two products do nearly all the work, and the choice between them comes down to what your alkalinity test says rather than how far the pH has fallen.
Soda ash, or sodium carbonate. Raises pH quickly with only a modest lift to alkalinity. Reach for it when pH is low, and alkalinity already sits inside the 80 to 120 ppm range.
Baking soda, or sodium bicarbonate. Raises alkalinity strongly and pH gently. Use it when both readings are low, and treat the pH rise as a side effect rather than the goal.
Borax. Moves pH with almost no effect on alkalinity. Useful for a small correction, though it leaves borates in the water, which changes how some test kits read afterward.
Dose by volume, never by eye. Work out the gallons, measure the product, dissolve it in a bucket of pool water, then pour it slowly in front of a return jet with the pump running. Give the water at least four hours to circulate before retesting. Stacking a second dose on top of an unmeasured first one is how pools end up cloudy, scaled, or both.
Raising pH without adding chemicals
Aeration lifts pH on its own and touches nothing else on the test strip. Moving water through air drives dissolved carbon dioxide out, and as the carbon dioxide leaves, pH climbs. Nothing goes into the pool, so alkalinity stays exactly where it was.
Water features earn their keep here, which is why we raise them at the design stage as part of how we install fiberglass pools. A spillover spa, a deck jet, or a sheer descent keeps the surface moving all day without anyone touching a test kit. On a pool that is already in the ground, point the return jets upward so they break the surface, run whatever feature you have, and leave the pump going longer than usual.
The trade-off is time. Aeration works in hours and days rather than minutes, which makes it a reasonable fix for a pool that is only slightly low and a poor one for a pool that needs correcting before the weekend.
How to test pH so the reading means something
A bad sample produces a bad decision, and most of the pH chasing we see traces back to how the water was collected rather than to the chemistry itself.
Reach down to elbow depth, away from the return jets and the skimmer, since surface water and jet water both read differently from the body of the pool. Test at the same time of day, because pH runs higher in the afternoon after hours of sun and surface movement. Read alkalinity in the same sitting, because a pH number on its own does not tell you which product to reach for.
While the kit is out, check cyanuric acid too, because chlorine without protection burns off in Florida sun within hours, and how stabilizer shields chlorine is worth knowing before you blame pH for a sanitizer that will not hold. Strips are fine for a quick look.
For a correction, a drop-based kit or a digital meter gives you something worth dosing against. Replace reagents every season, since expired ones drift and send you chasing a problem that is not there, and a meter that has never been calibrated is no better than a strip.
Keeping pH steady between tests
Steady pH is mostly a byproduct of a steady routine rather than a product you add. Get the buffer right, and the readings stop moving on their own.
Hold alkalinity near the middle of the 80 to 120 ppm band, and most weather swings stop registering. Rinse or backwash the filter on schedule so circulation stays even. Test after heavy rain and after a busy weekend rather than on a fixed calendar day, since those are the events that actually move the number. Store products somewhere cool and dry, because damp soda ash clumps and doses unpredictably. The rhythm we hand homeowners at the end of a build is laid out in a weekly pool care routine.
Surface matters as well. A fiberglass gel coat is nonporous, so it asks less of the chemistry than plaster does, and pH tends to sit flatter as a result.
Questions we hear most
The same handful of questions come up once the test kit is out and the numbers are not cooperating.
What is the ideal pH for a pool?
Between 7.2 and 7.6, with 7.4 as the comfortable middle. That band keeps chlorine working efficiently, protects metal components, and sits close enough to the pH of human tears that swimmers stop complaining about stinging eyes. Drifting slightly outside it for a day does no harm. Living outside it for weeks does.
Will baking soda raise pH or only alkalinity?
Both, though alkalinity moves far more. Baking soda is the right call when alkalinity is low, and pH is only slightly down. If alkalinity already sits in range and pH alone has fallen, soda ash does the job without pushing alkalinity above where you want it.
How long does it take for pH to come up?
A measured dose of soda ash usually registers within four to six hours of circulation, and the reading settles by the next day. Aeration is slower and can take several days, depending on how far down the pH started and how much surface movement the pool gets.
Can we swim while pH is being adjusted?
Wait until the product has fully dissolved and circulated, which generally means four hours with the pump running. Swimming sooner risks contact with undissolved granules sitting on the floor. Retest before anyone gets in, since a corrected pool still needs its chlorine reading checked.
Why does my pH keep dropping no matter what I add?
Low alkalinity is the usual culprit, because nothing is holding the pH in place. Trichlor tablets running constantly will do it as well. Correct alkalinity first, then revisit pH, and look at how much acidic sanitizer the pool takes in across a week.
Book a free water check
If the readings never settle, the cause is often structural rather than chemical. Returns aimed so that water sits still in a corner, a filter undersized for the volume, or a heater bypass left half open will all show up as chemistry that refuses to behave. We come out, look at the whole setup, and tell you what we find, with no obligation and no charge for the visit.
Hawaiian Island Pools
6040 Main St, New Port Richey, FL 34652
(727) 843-0423
Our services include:




Comments